Any environment can contain an
environment.conf file. This file can override several settings whenever the master is serving nodes assigned to that environment.
environment.conf file should be stored in an environment. It should be at the top level of its home environment, next to the
For example, if your environments are in the default directory (
test environment’s config file should be located at
# /etc/puppetlabs/code/environments/test/environment.conf # Puppet Enterprise requires $basemodulepath; see note below under "modulepath". modulepath = site:dist:modules:$basemodulepath # Use our custom script to get a git commit for the current state of the code: config_version = get_environment_commit.sh
environment.conf file uses the same INI-like format as
puppet.conf, with one exception: it cannot contain config sections like [
main]. All settings in
environment.conf must be outside any config section.
Relative paths in values
Most of the allowed settings accept file paths or lists of paths as their values.
If any of these paths are relative paths — that is, they start without a leading slash or drive letter — they will be resolved relative to that environment’s main directory.
For example, if you set
config_version = get_environment_commit.sh in the
test environment, Puppet will use the file at
Interpolation in values
The settings in
environment.conf can use the values of other settings as variables (such as
$codedir). Additionally, the
config_version setting can use the special
$environment variable, which gets replaced with the name of the active environment.
The most useful variables to interpolate into
environment.conf settings are:
$basemodulepath— useful for including the default module directories in the
modulepathsetting. Puppet Enterprise (PE) users should usually include this in the value of
modulepath, since PE uses modules in the
basemodulepathto configure orchestration and other features.
$environment— useful as a command line argument to your
config_versionscript. You can interpolate this variable only in the
$codedir— useful for locating files.
environment.conffile can override these settings:
The list of directories Puppet will load modules from.If this setting isn’t set, the
modulepathfor the environment will be:
That is, Puppet will add the environment’s modules directory to the value of the basemodulepath setting from
<MODULES DIRECTORY FROM ENVIRONMENT>:$basemodulepath
puppet.conf, with the environment’s modules getting priority. If the modules directory is empty of absent, Puppet will only use modules from directories in the basemodulepath. A directory environment will never use the global
The main manifest the Puppet master will use when compiling catalogs for this environment. This can be one file or a directory of manifests to be evaluated in alphabetical order. Puppet manages this path as a directory if one exists or if the path ends with a slash (
/) or dot (
If this setting isn’t set, Puppet will use the environment’s
manifestsdirectory as the main manifest, even if it is empty or absent. A directory environment will never use the global
A script Puppet can run to determine the configuration version.
Puppet automatically adds a config version to every catalog it compiles, as well as to messages in reports. The version is an arbitrary piece of data that can be used to identify catalogs and events.
You can specify an executable script that will determine an environment’s config version by setting
config_versionin its environment.conf file. Puppet will run this script when compiling a catalog for a node in the environment, and use its output as the config version.Note: If you’re using a system binary like
git rev-parse, make sure to specify the absolute path to it. If
config_versionis set to a relative path, Puppet will look for the binary in the environment, not in the system’s
If this setting isn’t set, the config version will be the time at which the catalog was compiled (as the number of seconds since January 1, 1970). A directory environment will never use the global
How long the Puppet master should cache the data it loads from an environment. If present, this will override the value of
environment_timeoutfrom puppet.conf. Unless you have a specific reason, we recommend only setting
environment_timeoutglobally, in puppet.conf. We also don’t recommend using any value other than
For more information about configuring the environment timeout, see the timeout section of the Creating Environments page.