Any environment can contain an
environment.conf file. This file can override several settings whenever the Puppet master is serving nodes assigned to that environment.
Each environment.conf file should be stored in an environment. It should be at the top level of its home environment, next to the
For example, if your environments are in the default directory (
test environment’s config file should be located at
# /etc/puppetlabs/code/environments/test/environment.conf # Puppet Enterprise requires $basemodulepath; see note below under "modulepath". modulepath = site:dist:modules:$basemodulepath # Use our custom script to get a git commit for the current state of the code: config_version = get_environment_commit.sh
The environment.conf file uses the same INI-like format as puppet.conf, with one exception: it cannot contain config sections like
[main]. All settings in environment.conf must be outside any config section.
Relative paths in values
Most of the allowed settings accept file paths or lists of paths as their values.
If any of these paths are relative paths — that is, they start without a leading slash or drive letter — they will be resolved relative to that environment’s main directory.
For example, if you set
config_version = get_environment_commit.sh in the
test environment, Puppet will use the file at
Interpolation in values
The settings in environment.conf can use the values of other settings as variables (e.g.,
$codedir). Additionally, the
config_version setting can use the special
$environment variable, which gets replaced with the name of the active environment.
The most useful variables to interpolate into environment.conf settings are:
$basemodulepath— useful for including the default module directories in the
modulepathsetting. Puppet Enterprise users should usually include this in the value of
modulepath, since PE uses modules in the
basemodulepathto configure orchestration and other features.
$environment— useful as a command line argument to your
config_versionscript. You can interpolate this variable only in the
$codedir— useful for locating files.
In this version of Puppet, the environment.conf file is only allowed to override five settings:
The list of directories Puppet will load modules from. See the reference page on the modulepath for more details about how Puppet uses it.
If this setting isn’t set, the modulepath for the environment will be:
<MODULES DIRECTORY FROM ENVIRONMENT>:$basemodulepath
That is, Puppet will add the environment’s
modules directory to the value of the
basemodulepath setting from puppet.conf, with the environment’s modules getting priority. If the
modules directory is empty or absent, Puppet will only use modules from directories in the
basemodulepath. A directory environment will never use the global
modulepath from puppet.conf.
The main manifest the Puppet master will use when compiling catalogs for this environment. This can be one file or a directory of manifests to be evaluated in alphabetical order. Puppet manages this path as a directory if one exists or if the path ends with a / or .
If this setting isn’t set, Puppet will use the environment’s
manifests directory as the main manifest, even if it is empty or absent. A directory environment will never use the global
manifest from puppet.conf.
A script Puppet can run to determine the configuration version.
Puppet automatically adds a config version to every catalog it compiles, as well as to messages in reports. The version is an arbitrary piece of data that can be used to identify catalogs and events.
You can specify an executable script that will determine an environment’s config version by setting
config_version in its environment.conf file. Puppet will run this script when compiling a catalog for a node in the environment, and use its output as the config version.
Note: If you’re using a system binary like
git rev-parse, make sure to specify the absolute path to it! If
config_versionis set to a relative path, Puppet will look for the binary in the environment, not in the system’s
If this setting isn’t set, the config version will be the time at which the catalog was compiled (as the number of seconds since January 1, 1970). A directory environment will never use the global
config_version from puppet.conf.
How long the Puppet master should cache the data it loads from an environment. If present, this will override the value of
environment_timeout from puppet.conf.
Unless you have a specific reason, configure only the
environment_timeout setting globally, in puppet.conf. Use only
unlimited as a value.
For more information about configuring the environment timeout, see the timeout section of the Configuring Environments page.
Static catalogs are generated by Puppet Server 2.3.0 and later. When enabled and configured, static catalogs can inline certain file metadata into the generated catalog.
static_catalogs setting is enabled by default in Puppet whether you upgrade Puppet or perform a clean installation, but Puppet does not generate static catalogs if Puppet Server is not configured with the scripts to handle them. A Ruby Puppet master never produces static catalogs, even when served by WEBrick or Passenger.
To disable static catalog generation for an environment, set the
static_catalogs setting in its environment.conf file to false on the Puppet Server master. To disable it globally, set
static_catalogs to false in Puppet Server’s puppet.conf file.